What should a natural latex mattress lie on?

The short answer: a flat, firm surface. It is the rule we print on our quotations: a platform, a solid base, our bed frame or the floor, and not bare slats or an old box base with springs. If your bed has slats, lay a board of plywood over them, cut to the inside of the frame. The calculator below gives the pieces and the sheets to buy.

Checked 20 November 2026

A bed on a solid built base in a timber villa room, a glass wall open on a garden of banana plants.

A flat surface, not slats

Our quotation says it in one line: the mattress must rest on a flat surface, not slats, so that it has balanced support and its air. Natural latex is supple. On slats set apart it sinks a little into every gap, and the support under you changes from one slat to the next.

Many latex makers abroad accept slats set close together, no more than about 7 cm apart. We ask for a flat surface all the same: it gives the same support under every part of the mattress, and the air does not need the gaps, because it moves through the latex itself, by the pin holes made in the mould.

A flat surface is also easy to make: a slatted bed is one board away from it.

Our mattress lying flat, seen from its foot end: the white top, the black piping, the quilted sides with Dominique Bienfait’s name.

Base by base

What each kind of bed base does under a natural latex mattress, and what to do about it.

Kinds of bed base under a natural latex mattress: flat or not, and what to do
The baseFlat?What to do
A platform, or a solid base of wood or concreteYesLay the mattress straight on it. In the rainy months, lift it now and then to air the underside.
Our bed frameYes: a top of laminated wood, 10 mm thickMade for our mattresses. Lay the mattress on it as it is.
SlatsNoLay a board of plywood over them, cut to the inside of the frame. The calculator below gives the pieces.
The floorYesIt gives the support. It gives the underside no air: lift the mattress often in humid months.
An old box base with springsNoA box spring is made to give. Set the mattress on a solid base instead.
A divan with a solid topIf the top does not givePress the top hard with your hand. If it gives, treat it as a box base.

If your bed has slats: one board

Hardware shops in Thailand sell plywood in sheets of 120 x 240 cm, and many cut it to measure. One sheet covers a Single or a Twin. A Queen or a King takes two pieces, each half the width, from two sheets: a board in two halves also goes up in a condominium lift and through a bedroom door.

Our bed frame alone, upholstered in grey cotton, its top in two halves, on short legs, on black.

Measure the inside of the frame, where the slats are, at the head and at the foot, and have each piece cut a little smaller than the frame so it drops in. For the thickness: our own bed frame carries a top of laminated wood 10 mm thick, on a reinforced frame. The further apart your slats stand, the thicker the board should be; tell the shop the gap and let it advise you.

On the board, the latex has its flat surface, and the air still moves through it by its pin holes. In the rainy months, lift the mattress from time to time, as you would on a platform.

The board for your bed, worked out

Type the inside of your bed frame, or pick the frame made for one of our sizes. You get the pieces to have cut, and the sheets of plywood to buy.

Or the frame for one of our sizes

2 pieces, each 75 x 200 cm

From 2 sheets of plywood, 120 x 240 cm

Have each piece cut a little smaller than the frame, so it drops in. The pieces of a board in halves meet in the middle of the bed.

On the floor

Many people in Thailand sleep close to the floor, and a latex mattress can lie there: the floor is flat, so the support is right. What the floor does not give is air underneath. In a humid room the underside of a mattress on the floor stays damp, and damp is where mould begins.

Our mattress lying straight on a black floor, seen from its foot end.

So lift it. In the rainy months, every week or two, stand it on its side against a wall for a few hours, with the window open or the air-conditioner on, and wipe the floor dry under it. A low platform under it does the same work every night.

Our mattress on our dark bed frame, a topper rolled back on it, two pillows and a bolster, in the black studio.

Our bed frame

We make a bed frame for our mattresses, by hand, in our workshop in Bangkok: a reinforced solid wood structure, a top of laminated wood 10 mm thick, the top and sides upholstered in thick cotton, the underside closed in white cotton, and legs of solid wood. It is made in Single, Queen and King, and in other sizes on request.

Our mattress on our bed frame, the white quilted mattress on the grey upholstered base, on black.

Not sure what your own bed needs? Send us a photograph of it and its inside measure on WhatsApp on +66 89 108 8889 (English, French) or +66 83 980 5623 (English, French, Thai), or through the contact form. We tell you what it needs, or make the mattress to fit it, and Dominique comes to see the bed when you ask.

Questions we are often asked

Can I put a latex mattress on slats?

We ask for a flat surface instead. Lay a board of plywood over the slats, cut to the inside of the frame, and the mattress has it.

How far apart should slats be for a latex mattress?

Latex makers abroad often say no more than about 7 cm. Ours asks for a flat surface rather than slats at all: a board over them settles the question.

Can a latex mattress go on the floor?

Yes, the floor is flat. Lift the mattress often in the humid months, stand it against a wall for a few hours, and dry the floor under it: a damp underside is where mould begins.

Can I use a box spring with a latex mattress?

A box spring is made to give, and latex wants a base that does not. Set it on a solid base, a platform or the floor.

What thickness of plywood goes under a mattress?

Our own bed frame carries a top of laminated wood 10 mm thick on a reinforced frame. Over slats that stand far apart, a thicker board bends less: tell the shop the gap between your slats.

Does a latex mattress need air underneath?

Air moves through our latex by its pin holes, so it does not need gaps under it. On a solid base or the floor, lift it from time to time in the rainy months to air the underside.

Natural Living Concept, Bangkok.

First published 20 November 2026. Checked 20 November 2026.

Prices in baht, VAT included. The shop page shows the price that applies.

If you have a question, call +66 89 108 8889, or write to us on WhatsApp.

Read next

Read on

What is natural latex? 100% vs blended latex

Natural latex is a foam made from the sap of the rubber tree.

Come and lie on one

The showroom is inside our workshop in Prawet, Bangkok. Tell us a day that suits you and we confirm the time.

322 Soi 16, Pattanakarn 61
Prawet, Bangkok 10250

Directions (opens in a new tab) 

  • Monday to Friday, 9:00 to 18:00
  • Saturday, 9:00 to 17:00

Monday to Friday, 9:00 to 18:00; Saturday, 9:00 to 17:00

Arrange a visit
© OpenStreetMap contributors (opens in a new tab)